Lathe bed regrinding service: If your existing lathe is worn but in good mechanical condition, we offer regrinding and refitting. Your lathe can be brought back to new or sometimes better than it was new - accuracy, at a fraction of the cost of new replacement. This service is available for lathes with beds up to 18' in overall length. For examples click here:

USED LATHES:

Aris Titan Model SNB560X3000 22" Swing,  120" Centers, 2-1/2" Bore, 24 speeds 20 - 1600 RPM, C/W Taper Attachment, 3-jaw chuck, steady rest, 4-way tool post, work light

Price:..........................................................................................$13,000.00 C

  Aris Titan SNB560

Cri-Dan Model BMK Threading Lathe, 15" Swing, 36" Centers, C/W: 8" 3-Jaw Chuck,

Price:......................................................................................$ 6,500.00 E

1 Used HERBERT Model No. 2 Turret LathE c/w 2 Position Toolholder in back & 4 Position Toolholder in front, & lamp 3 Ph B06-5332                       

PRICE………………………………….$4,500.00 V

1 USED HERBERT MODEL 2D TURRET LATHE, 13” SWING, 20” CENTERS, 16 SPEEDS 50 – 2550 RPM, C/W: COLLET CHUCK, 4 WAY TOOL POST, REAR TOOL POST ON FRONT CARRIAGE, 6 POSITION TURRET ON REAR CARRIAGE, 4 BORING BAR HOLDERS,

PRICE………………………………….$ 1,900.00 C

Herbert No. 2 Senior Turret lathe........................................$ 2,500.00 C       

MAS Model AB80 Semi-Automatic Lathe B01-3525 "as is"....$ 1,000.00 C

Microcut Model C6232E-1, 14" swing, 40" centers, S/N 8316, 220v/3PH/60HZ, B05-4871

PRICE………………………………......................................$ 5,900.00 V

1 USED MASTEEL MODEL ML2080IV 20” SWING, 28” IN GAP, 80” CENTERS, 4-1/8” BORE, INFINITELY VARIABLE SPINDLE SPEEDS 20 – 1600 RPM, VARIABLE FREQUENCY DRIVE, constant surface speed on cross slide, c/w: 12” 3-jaw, 16” 4-jaw, taper attachment, steady rest, follow rest, 4-way toolpost, coolant system, one piece cast base, excellent condition

price:………………………………...$ 21,500.00 c                       lease $ 455.00

1 Demo MASTEEL Model #ML-32120 HEAVY DUTY HOLLOW SPINDLE LATHE, 32” SWING, 120” CENTERS, 5-1/2” SPINDLE BORE, 40” SWING IN GAP, D1-11 CAMLOCK, 18 SPEEDS 5.4 – 720 RPM, INCH/METRIC THREADING, TAILSTOCK TAPER #5 MT, MAIN MOTOR 20 HP, CSA ELECTRICS, CW: RAPID TRAVERSE, 20” 3-JAW CHUCK, 20” 4-JAW CHUCK, 32” FACEPLATE, TAPER ATTACHMENT, THREAD DIAL, STEADY REST, FOLLOW REST, COOLANT, WORK LAMP, TOOL KIT, DEAD CENTERS, HEAVY DUTY CAST IRON BASE c/w Fagor Prokit DRO, 480 Volt, 3 Ph, Serial #GM-1461

PRICE……………………………….$39,900.00 V

1 USED MICROCUT MODEL C6232E-1 14” X 40” LATHE, S/N 8316, 220v/3PH/60HZ, B05-4871

PRICE…………SPECIAL…………$ 4,900.00 V

1 USED MONARCH MODEL EE TOOL ROOM LATHE, 12” SWING, 20” CENTERS, VARIABLE SPINDLE SPEEDS 0 – 4,000 RPM, COMPLETE THREADING RANGE, C/W: 5” 3-JAW CHUCK, 10” FACE PLATE, TAPER ATTACHMENT, COOLANT SYSTEM, CARRIAGE STOP

PRICE……………………………..$ 8,500.00 C

1 USED Nardini Model NI 2580T 25" Swing, 80" Centers,  5” SPINDLE BORE, (12) SPEEDS 16 – 1250 RPM, C/W: 24-3/4” 4-JAW CHUCK, TAPER ATTACHMENT, COOLANT,

Price:.................Reduced......................$ 18,500.00 C

Nardini 2580

1 USED PBR HEAVY DUTY MODEL TM350P LATHE, 28” SWING, 4” SPINDLE BORE, 36” SWING IN GAP, 120” CENTERS, 24 SPEEDS 10 – 1000 RPM, 15/20 HP MAIN MOTORC/W: 3-JAW CHUCK, 4-JAW CHUCK, STEADY REST, TAPER ATTACHMENT, APPROXIMATE NET WEIGHT 12,230 LBS

PRICE…………SPECIAL…………$ 21,000.00 C                      LEASE $ 437.00

    PBR TM350P

STANDARD MODERN 9” UTILATHE, 9” X 22”, ½ HP, 8 SPEEDS 50 – 1500 RPM, 13/16” SPINDLE BORE, C/W: 5” 3-JAW CHUCK, 6” 4-JAW CHUCK, 8” FACEPLATE, TAPER ATTACHMENT, CABINET STAND,

PRICE……………………………….......................................$ 2,500.00 E

1 USED STANDARD MODERN 9” UTILATHE, 9” X 22”, ½ HP, 8 SPEEDS 50 – 1500 RPM, 13/16” SPINDLE BORE, C/W: 5” 3-JAW CHUCK, 6” 4-JAW CHUCK, 8” FACEPLATE, TAPER ATTACHMENT, CABINET STAND,

PRICE………………………………..$ 2,500.00 E

1 USED SUMMIT 19-4-80 19” SWING, 80” CENTERS, 4” SPINDLE BORE, SPEEDS 22 – 1,500 RPM, c/w: 12” 3-jAW CHUCK, QUICK CHANGE TOOLPOST, TAPER ATTACHMENT, COOLANT SYSTEM, S/N: 3254586

PRICE:…………Reduced…..$ 6,000.00 C           

1 used summit 23-4-120 23"  Swing, 120" centers, 4" spindle bore, 36" swing over gap, 25" wide removable gap, 16" wide bed, 16" cross feed, 16" swing over cross slide, c/w: taper turning attachment, rapid traverse, 2 steady rests, 3-jaw chuck, 4-jaw chuck, 220V/440V 3 phase Electrics, S/N:810914

Price:.....................F.O.B. Estevan Saskatchewan........$18,750.00 (Consignment)

        Summit 23-4-120

1 USED TARNOW MODEL TUJ50M/2500 LATHE, 20” X 100”, 15 HP, 18 SPEEDS 10 – 1600 RPM, 3-1/2” BORE, C/W: 20” 4-JAW CHUCK, TAPER ATTACHMENT, 40 POSITION TOOLPOST, STEADY REST,

PRICE…………………………………$ 13,500.00 E

1 USED TOS MODEL SN40B 16” SWING X 80” CENTERS LATHE, 2” SPINDLE BORE, 24 SPEEDS: 22.5 – 2000 RPM, C/W: 12” TAYLOR 3-JAW CHUCK, TAPER ATTACHMENT, 4-WAY TOOL POST, 480V/3/60 ELECTRICS, REGROUND BEDWAYS – NEW ACCURACY                                                                                 

PRICE……………………………………$ 10,500.00 C                     LEASE $ 273.00

1 USED VDF MODEL 3VK HD LATHE, 20” SWING, 3-1/8” SPINDLE BORE, 80” CENTERS, 7-1/2 HP MOTOR, NO ACCESSORIES,

PRICE…………………AS IS……..$ 5,000.00 C

1 USED VDF MODEL V5 LATHE S/N 14798, 27” SWING, 120” CENTERS, 3” SPINDLE BORE, 18 HP MOTOR, 18 SPEEDS 11.2 – 560 RPM, C/W 20” 4-JAW CHUCK, TAPER ATTACHMENT, COOLANT

PRICE………………….SPECIAL….$ 16,000.00 E                    LEASE $ 416.00

1 USED VDF MODEL E700 LATHE, 35” SWING, 120” CENTERS, 2-3/4” BORE, 12 SPEEDS 63 – 800 RPM, 25 HP, 31” 4-JAW, 2 sTEADIES, TAPER, 4-WAY TOOL POST, S/N 3414

PRICE…………………SPECIAL ….$ 12,000.00 E                      LEASE $ 312.00

1 USED VOEST MODEL DA250X2000, 20” SWING, 80” CENTERS, 18 SPEEDS 21 – 1,500 RPM, 7-1/2 HP MOTOR, c/W: 12” 3-JAW CHUCK, 14” 4-JAW CHUCK, STEADY REST, FOLLOW REST, COOLANT, 4 WAY TOOLPOST, TAPER ATTACHMENT S/N: 037213869

PRICE:…………………SPECIAL…..$ 7,500.00 C

1 USED WAFUM MODEL TUR560/2000 LATHE, 21” X 80”, 20 HP, 3-1/2” SPINDLE BORE, C/W: 12” 3-JAW CHUCK, STEADY REST, FOLLOW REST, 40 POSITION TOOLPOST,

PRICE………………………………….$ 14,500.00 E

1 USED WEISSER HEILBRON lathe, 23” x 120” centers, 15-1/2” over cross slide, 32” over gap, 15 hp, 18 speeds 18 – 900 rpm, 2-1/2” spindle bore, c/w: 20” 4-jaw chuck, taper attachment, coolant system, multi-fix style 40 POSITION quick change tool post & 3 TOOL HOLDERS

price……………………special…$ 16,000.00 c                     lease $ 416.00

1 Used YAMAZAKI MAZAK 30” x 132” Gap Bed Lathe, 4” Feed Thru, 12-1200 RPM Chip Guard 4-Jaw Chuck, Steadyrest, Quick Change Toolpost, Serial #M9041468Y07 B05-5093

PRICE…………………………………..$19,000.00 V